Ready Mix Plaster
Packaging: 50 Kg Bag
SARWIN Ready-Mix Plaster 1:4 Ratio is manufactured in modern dry mix plant with computerized batch process.
Plaster is ready to use by just mixing water at site. This process eliminates job-site mixing practices. Hence it
gives consistent quality with required sand mesh sizes in exact proportion which is most important for compactness of plaster. Further to have desired workability, less rebounding losses, required slump properties and overall durability, polymers are added in Sarwinplast Ready-Mix Plaster.
Super
Strength
Extra
Bonding
Super
Coverage
Smooth
Finishing
METHOD OF USAGE
PREPARATION, MIXING & APPLICATION:
- The substrate needs to be clean and free from dust, grease and Loose adhering particles, etc. else it will affect the bonding of the plaster to the surface.
- The porous and absorbent substrates need to be pre-wetted prior to application of Sarwinplast Ready-Mix Plaster to prevent premature loss of water from the plaster
- This will ensure that thin layer can be applied without cracking problems and proper cement hydration and adherence of the mortar to the substrate is attained.
- Use 9-10 liters of clean water per every 50 kg of Sarwinplast Ready-Mix Plaster
- Pour the Sarwinplast Ready-Mix Plaster while mixing for 5-10 minutes with hand or mechanical mixer is recommended for better result and achieve a good consistency
- Do not over mix (Depending on the speed of mixing equipment
- Allow mixture to stand for 5 minutes for additives to dissolve completely. Re-mix again for about 2 minutes just before use.(Do not over mix
- Now add water to the mixture. Hard and set plaster should not be mixed again
- The correct ratio of water and Sarwinplast Ready-Mix Plaster is essential for excellent plastering.
- Apply plaster to the substrate, using some pressure while finishing with a steel trowel or wooden float to ensure optimum bonding of the plaster to the substrate surface.
- For better sticking of the plaster, the prepared surface should be rough.
- Once the mixture is prepared, it should be applied within one hour.
- Sarwinplast Ready-Mix Plaster can be used for exterior and well as interior wall
HOW TO APPLY:
- The substrate needs to be cleaned and made free from grease and loose particles. Then dampen the surface with water.
- Add Ready-mix plaster to potable water and mix well for 5 to 10 mins
- Allow mixture to stand for 5 mins and then remix again for 2 mins.
- Apply plaster to the substrate, using some pressure while finishing with a steel trowel or wooden float to ensure optimum bonding.
- Apply aluminum level patty from bottom to top direction followed by left to right and right to left direction to level the plaster.
- Post 24 hours curing recommended for 7 days.
CAUTION:
- Do not use hook
- Store in a cool dry place
- Increase of contact with eyes for open wound rings out quickly with fresh water
WATERING & SATURATION
Sarwinplast Ready-Mix Plaster doesn’t need watering for 24 hours in normal weather. Once the plaster is dried and set completely watering should be done once or twice for 3-4 days and 5-7 days required in abnormal weather condition
Key Features
- Compact plaster, reduce void gaps
- Negligible silt content
- Reduces rebounding loss
- Highly durable plaster that cuts repair the maintenance cost
- Frequent watering /Saturation not required
- Excellent workability and good adhesion on various substrates
- Smooth plastering
- Smooth finish
- Time-Saving
- Cost-Effective
Coverage:
Sarwinplast Ready-Mix Plaster approx. coverage per 50 kg bag is as under: 8-12 mm plaster on Bricks and blocks is 25-30 sq. ft. Coverage depend on quality and nature of substrates hence is indication. Plaster >More than 08-12 mm thickness must be in 2 coats.
Ready-mix Product Range:
1:6 Normal Plaster
1:5 Normal Wall Plaster
1:4 Sealing Plaster
1:4 Polymerised all Plaster
